piping engineer interview questions
When interviewing piping engineers particularly the lead piping engineers and the piping design engineers, questions asked to the candidate are likely to be geared towards testing his technical competency, his management skills and his experience. Areas which should be reviewed include piping design, stress analysis, material selection and the ratios of the company should adhere to standards such as ASME and ANSI. Questions often cover skills in using AutoCAD, CAESAR II, and other similar programs.
Job seekers should be ready to speak on aspects of cost control and estimation, management of risks, constructions, and maintenance. Problem solving skills, teamwork and communication skills are also assessed Being the most important aspect among all the soft skills, problem solving skills As for teamwork, the specific abilities to be assessed are: As for communication skills, the specific aspects that are to be evaluated include: To this end, it is recommended that a piping engineer needs to have adequate resources such as the “Piping Engineer Interview Questions and Answers” PDFs to prepare for the interviews.
1. What are the steps in selecting a valve?
What to handle, liquid, gas or powder, fluid nature, function, construction material, disc type, stem type, how to operate, bonnet type, body ends, delivery time, cost, warranty.
2. What are the functions of valves?
Isolation, regulation, non-return and special purposes.
3. What are isolating valves?
Gate, ball, plug, piston, diaphragm, butterfly, pinch.
4. What are regulation valves?
Globe, needle, butterfly, diaphragm, piston, pinch.
5. What are non-return valves?
Check valve
6. What are special valves?
Multi-port, flush bottom, float, foot, pressure relief, breather.
7. What materials are used for construction of valves?
Cast iron, bronze, gun metal, carbon steel, stainless steel, alloy carbon steel, polypropylene and other plastics, special alloys.
8. What is trim?
Trim is composed of stem, seat surfaces, back seat bushing and other small internal parts that normally contact the surface fluid.
9. Which standard specifies trim numbers for valves?
API 600.
10. What are wetted parts of the valve?
All parts that come in contact with surface fluid are called wetted parts.
11. What is wire drawing?
This term is used to indicate the premature erosion of the valve seat caused by excessive velocity between seat and seat disc, when the valve is not closed tightly.
12. What is a straight through valve?
Valve in which the closing operation of the valve is achieved by 90 degrees turn of the closing element.
13. What pressure tests are carried out on valves?
Shell-hydrostatic, seat-hydrostatic, seat-pneumatic
14. What are available valve operators?
Hand Lever, handwheel, chain operator, gear operator, powered operator like electric motor, solenoid, pneumatic and hydraulic operators, Quick acting operators for non-rotary valves (handle lift).
15. What are two types of ball valve?
Full port design and regular port design, according to type of seat, soft seat and metal seat.
16. What are ball valve body types?
Single piece, double piece, three piece, the short pattern, long pattern, sand witch and flush bottom design.
17. Why are ball valves normally flanged?
Because of the soft seat PTFE which can damage during welding.
18. What are butterfly valve types?
Double flange type, wafer lug type and wafer type.
19. What are the types of check valves?
Lift check valves and swing check valves.
20. What are non-slam check valves?
Swing check valve, general check valve, wafer check valve, tilting disc check valve, piston check valve, stop check valve, ball check valve.
21. Where does the stop check valve is used?
In stem generation by multiple boilers, where a valve is inserted between each boiler and the main steam header. It can be optionally closed automatically or normally.
22. Where diaphragm valves are used?
Used for low pressure corrosive services as shut off valves.
23. What is a barstock valve?
Any valve having a body machined from solid metal (barstock). Usually needle or globe type.
24. What is a BIBB valve?
A small valve with a turned down end, like a faucet.
25. What is a bleed valve?
Small valve provided for drawing off liquid.
26. What is a blowdown valve?
Refers to a plug type disc globe valve used for removing sludge and sedimentary matter from the bottom of boiler drums, vessels, drip legs etc.
27. What is a breather valve?
A special self acting valve installed on storage tanks etc. to release vapor or gas on slight increase of internal pressure ( in the region of ½ to 3 ounces per square inch).
28. What is a drip valve?
A drain valve fitted to the bottom of a droplet to permit blowdown.
29. What is a flap valve?
A non return valve having a hinged disc or rubber or leather flap used for low pressure lines.
30. What is a hose valve?
A gate or globe valve having one of its ends externally threaded to one of the hose thread standards in use in the USA. These valves are used for vehicular and firewater connections.
31. What is a paper-stock valve?
A single disc single seat gate valve (slide gate) with knife edged or notched disc used to regulate flow of paper slurry or other fibrous slurry.
32. What is a root valve?
A valve used to isolate a pressure element or instrument from a line or vessel, or a valve placed at the beginning of a branch from the header.
33. What is a slurry valve?
A knife edge valve used to control flow of non-abrasive slurries.
34. What is a spiral sock valve?
A valve used to control flow of powders by means of a twistable fabric tube or sock.
35. What is a throttling valve?
Any valve used to closely regulate flow in the just-open position.
36. What is a vacuum breaker?
A special self-acting valve or any valve suitable for vacuum service, operated manually or automatically, installed to admit gas (usually atmospheric air) into a vacuum or low-pressure space. Such valves are installed on high points of piping or vessels to permit draining and sometimes to prevent siphoning.
37. What is a quick acting valve ?
Any on/off valve rapidly operable, either by manual lever, spring or by piston, solenoid or lever with heat-fusible link releasing a weight which in falling operates the valve. Quick acting valves are desirable in lines conveying flammable liquids. Unsuitable for water or for liquid service in general without a cushioning device to protect piping from shock.
38. What is a diverting valve ?
This valve switch flows from one main line to two different outlets. WYE type and pneumatic control type with no moving part.
39. What is a sampling valve?
Usually of needle or globe pattern, placed in branch line for the purpose of drawing all samples of process material thru the branch.
40. What is a blow off valve?
It is a variety of globe valve confirming with boiler code requirements and specially designed for boiler blowoff service. WYE pattern and angle type, used to remove air and other gases from boilers etc.
41. What is a relief valve?
Valve to relieve excess pressure in liquids in situations where full flow discharge is not required, when release of a small volume of liquid would rapidly lower pressure.
42. What is a safety valve?
Rapid opening (popping action) full flow valve for air and other gases.
43. What is a foot valve?
Valve used to maintain a head of water on the suction side of the sump pump, basically a lift check valve with integrated strainer.
44. What is a float valve?
Used to control liquid level in tanks, operated by float, which rises with liquid level and opens the valve to control water level. It can also remove air from the system, in which case, air flows out of the system in valve open condition, but when water reaches the valve, the float inside valve raises to close the valve and stop flow of water. Used in drip legs.
45. What are flush bottom valves?
Special type of valves used to drain out the piping, reactors and vessels, attached on pad type nozzles.
46. What are types of flush bottom valves?
Valves with discs opening into the tank and valves with disks into the valve.
47. What are the uses of three-way valves?
Alternate connection of the two supply lines to a common delivery vise versa, isolating one safety valve, division of flow with isolation facility.
48. What are the uses of a four way valve?
Reversal of pump suction and delivery, Bypass of strainer or meter, reversal of flow through filter, heat exchanger or dryer.
49. What is a metal seated lubricated plug valve?
A plug valve with no plastic material, where grease is applied to contacting surfaces for easy operation.
50. What are three patterns of plug valve design?
Regular pattern, short pattern and venturi pattern.
piping engineering interview questions and answers
What is a regular pattern plug valve?
Rectangular port, area almost equal to pipe bore, smooth transition from round body to rectangular port, for minimum pressure loss.
What are short pattern plug valves?
Valves with face to face dimension of gate valve, as an alternative to gate valve.
What are venturi pattern plug valves?
Change of section through the body throat so graded to have venturi effect, minimum pressure loss.
What are inverted plug design valves?
Plug valve with taper portion up of plug. For 8” and higher size.
What is a pressure balanced plug valve?
With holes in port top and bottom connecting two chambers on top and bottom of plug, to reduce turning effort.
What are teflon sleeved plug valves?
PTFE sleeve between plug and body of valve, low turning effort, minimum friction, temperature limitation, anti static design possible.
What are permaseal plug valves?
Plug valves with teflon seat instead of sleeves, for on off applications, can handle clean viscous and corrosive liquids, graphite seat for high temperature applications. Drip tight shut off is not possible.
What are eccentric plug valves?
Off center plug, corrosive and abrasive service, on off action, moves into and away from the seat eliminating abrasive wear.
What is the dimensional standard for plug valves?
API 599.
What is a pinch valve?
Similar to diaphragm valves, with sleeves of rubber or PTFE, which get squeezed to control or stop the flow, cast iron body, for very low service pressures like isolation of hose connections, manufacture standard.
What is a needle valve?
Full pyramid disc, same design as globe valve, smaller sizes, sw or threaded, flow control, disc can be integral with stem, inside screw, borged or barstock body and bonnet, manufacturers standard.
How to install a globe valve?
Globe valves should be installed such that the flow is from the underside of the disk, Usually flow direction is marked on the globe valve.
What are globe valve port types?
Full port: More than 85% of bore size, Reducer port: One size less than the connected pipe.
What are globe valve disk types?
Flat faced type for positive shutoff, loose plug type for plug renewal or needle type for finer control.
What are the characteristics of globe valve stem?
Always rising design, with disk nut at the lower end and handwheel at upper end.
What are the types of globe valves?
Angle globe valve, plug type disc globe valve, wye-body globe valve, composite disc globe valve, double disc globe valve.
What is an angle globe valve?
Ends at 90 degrees to save elbow, higher pressure drop.
Where plug type disc globe valve is used?
For severe regulating service with gritty liquids such as boiler feedwater and for blow off service.
Where is the WYE body globe valve used?
In line ports with stem emerging at 45 degree, for erosive fluids due to smoother flow pattern.
What is a double disc globe valve?
Has two discs bearing on separate seats spaced apart, on a single shaft, for low torque, used for control valves.
What are port types for gate valves?
Full port and reduced port. Default is reduced bore. Full port has to be specified in bom.
How to close a gate valve?
Turn the handwheel in a clockwise direction.
What is a lantern ring?
It’s a collection point to drain off any hazardous seepages or as a point where lubricant can be injected, it is in the middle of packing rings.
What are types of gate valves?
Solid plane wedge, solid flexible wedge, split wedge, double disc parallels seats, double disc wedge, single disc single seat gate or slide, single disc parallel seats, plug gate valve.
What are the types of bonnets?
Bolted bonnet, below sealed bonnet, screwed on bonnet, union bonnets, A U-bolt and clamp type bonnet, breech lock bonnet, pressure seal bonnet.
piping engineer interview questions and answers
1. What is the ASME code followed for design of piping systems in Process piping (Refineries & Chemical Industries)?
A) B31.1 B) B31.3 C) B31.5 D) B31.9
Ans: (B)
2. What do you mean by the following items?
A) ISLB-400 B) ISMB-600 C) ISHB-350 D) ISMC-300 E) ISJB-150 F) ISLB-200 G) ISMB-450 H) ISWB-400 I) ISJC-200 J) ISLC-350 K) ISMC-250
A)Indian STD light weight beam, Web size – 400
B)Indian STD medium weight beam, Web size – 600
C)Indian STD ‘H’ beam, Web size – 350
D)Indian STD medium weight channel, Web size –300
E)Indian STD junior beam, Web size – 150
F)Indian STD lightweight beam, Web size – 200
G)Indian STD medium weight beam, Web size – 450
H)Indian STD wide flange beam, Web size – 400
I)Indian STD junior channel, Web size – 200
J)Indian STD lightweight channel, Web size – 350
K)Indian STD medium weight channel, Web size – 250
3. What is this item?
A) ISA-100X100X12 B) ISA-80X50X10 C) ISLT-100X100
A) Equal angle size 100 x 12 THK,B) Unequal angle size 80x50x10 THK,C) Indian STD lightweight tee bar size 100x100
4. What is the difference between stub in and stub on branches? Which one is preferred?
For branching of one size lesser of run pipe, Stub On is preferred. For other branching less than one size of run pipe stub in is preferred. The Design is based on ANSI B 31.3
5. What is the difference between Pipe and Tube?
Pipe is identified by NB and thickness is defined by Schedule whereas Tube is identified by OD.
6. From which size on wards NB of pipe is equal to OD of Pipe?
From the size 14” and on wards NB = OD of pipe.
7. Write down the outside diameter of the following pipe?
A) 3 inch B) 6 inch C) 10 inch D) 14 inch
A)3 inch = 88.9mm ,B)6 inch = 168.28mm,C)10 inch = 273.06mm,D)14 inch = 355 mm (OD= SizeX25.4)
8. What is the difference between machine bolt and stud bolt?
Machine bolt has a head on one side and a nut on the other side but stud bolts have nuts on both sides.
9. What is a soluble dam?
Soluble dam is a water-soluble material used for restricting the purging gas within the pipe.
10. While welding the pipe trunnion to pipe/reinforcement pad you have to put a hole or leave some portion of welding why?
For venting of hot gas which may get generated due to welding.
11. What do you mean by the following type of welding?
1. SMAW 2. TIG
Ans: SMAW = SHIELDED METAL ARC WELDING, TIG = TUNGSTEN INERT GAS WELDING.
12. What should be the radius of a long elbow?
1.5D (Where “D” is the diameter of the pipe)
13. Normally where do we use the following?
A) Eccentric reducers (ER) B) Concentric reducers (CR)
A)ER = Pump suction to avoid Cavitations, to maintain elevation (BOP) in rack,B)CR = Pump discharge, vertical pipeline etc.
14. Concentric reducer is used in pump suction. (Yes / No). Explain.
No. Air pockets may form if concentric reducer is used at pump suction, which results in Cavitations, and cause damage to Pump. To avoid this problem, Eccentric Reducer with Flat Side Up (FSU) is used in Pump Suction.
15. What do you mean by Cavitation in Pump?
A pump is designed to handle liquid, not vapor. Vapor forms if the pressure in the pump falls below the liquid’s vapor pressure. The vapor pressure occurs right at the impeller inlet where a sharp pressure drop occurs. The impeller rapidly builds up the pressure which collapses vapor bubbles causing cavitation and damage. This is avoided by maintaining sufficient NPSH.
(Cavitation implies cavities or holes in the fluid we are pumping. These holes can also be described as bubbles, so cavitation is really about the formation of bubbles and their collapse. Bubbles form whenever liquid boils. It can be avoided by providing sufficient NPSH.)
16. What do you mean by NPSH? How do you calculate it?
NPSH = Net Positive Suction Head. NPSH is the pressure available at the pump suction after vapor pressure is subtracted. It is calculated as: Static head + surface pressure head - the vapor pressure of your product - the friction losses in the piping, valves and fittings. It thus reflects the amount of head loss that the pump can sustain internally before vapor pressure is reached.
17. What is the ASTM code for the following?
A) CS pipe B) CS fittings C) CS flanges D) AS pipe P5/P11 E) Cast CS Valves
A) CS pipe = A106 Gr.B, B)CS fittings = A234 Gr.WPB/WPBW, C)CS flanges = A105, D)AS pipe = A335 Gr P5/P11, E)Cast CS Valves = A216 Gr. WCB
18. What is the thumb rule to calculate spanner size for a given bolt?
1.5 x diameter of Bolt
19. What is the thumb rule to calculate Current required for Welding?
Current (Amp) = [Diameter of Electrode (mm) X 40] + 20
20. What is steam tracing? How do we decide the location of SSM & CRM?
Steam Tracing is a process which is used to prevent the fluid passing through a process line from freezing by keeping the temperature high enough for free flow of fluid and thus maintaining palpability. SSM and CRM are generally located 38M max for open system and 24 M max for closed system when we use LP Steam up to 3.5-kg/sq cm. as a heating media.
21. Which piping items will you drop down before conducting Flushing and Hydro tests?
Items like Control Valve, Orifice plates, Rotameters, safety valves; Thermo wells are dropped or replaced with temporary spools before hydro test.
22. Why do we provide a Dampener in the Piping of Reciprocating Pump?
To take care of Pulsation.
23. Why do we provide Full Bore Valve in the connecting pipeline of Launcher/Receiver?
For Pigging.
24. Which parameters will you check during checking Piping Isometrics?
Bill of Material, Pipe Routing w.r.t. GAD, Supporting arrangement, details of insulation, hydro test pressure, painting specs and provision of Vent and Drains at appropriate locations.
25. What is the ANSI/ASME dimensional standard for steel flanges & fittings?
A) B16.3 B) B16.5 C) B16.9 D) B16.10
Ans: (B)
26. How can flanges be classified based on facing?
A. Flat Face B. Raised Face C. Tongue and groove D. Ring type joint
27. What do you mean by AARH (Flange Finish)?
Arithmetic Average Roughness Height.
28. Which are the different types of Gaskets?
Full Face, Spiral Wound, Octagonal Ring Type, Metal Jacketed and Inside Bolt Circle.
29. What should be the relative hardness between the RTJ gasket and flange groove?
For a RTJ flange, the joint ring should have a 30-40 Vickers hardness less than that of the mating face of the flange. (Brinell hardness for RTJ groove shall be 20-50 BHN more than the corresponding gasket hardness)
30. From which side of the pipe will you take a branch connection?
When Fluid is Gas, Air or Steam and Cryogenic Service – Topside. When Fluid is Liquid – Bottom Side.
31. Why don’t we take a branch for Cryogenic Service from the bottom side though the fluid is in liquid state?
There is the chance of Ice formation during normal operation and since ice flows from the bottom of the pipe it will block the branch pipe connection.
32. Why do we provide Drip Leg in Steam Line?
To remove Condensate when there is a rise in the pipe along the flow direction. If we do not provide the drip leg in the steam line, the condensate which forms inside the pipe will result in the Water Hammer effect causing damage to the piping system.
33. Which standard and codes will you refer to while designing the piping?
Following are the codes and standards –
ASME SEC I: Rules for construction of Power Boilers.
ASME SEC VIII: Rules for construction of Pressure Vessels.
ASME B 31.1: Power Piping
ASME B 31.3: Process Piping
ASME B 31.4: Pipeline Transportation system for liquid hydrocarbon & other liquids.
API RP 520: Sizing selection and installation of Pressure Relieving Devices in refineries
API Std 610: Centrifugal Pumps for Petroleum, Heavy Duty Chemical and Gas Industry Services.
ANSI/NEMA SM 23: Steam Turbines for Mechanical Drive Services.
API Std 617: Centrifugal Compressor for Petroleum, Chemical and Gas Industry Service.
EJMA: Expansion Joints Manufacturer’s Association.
OISD – 118: Layout for Oil and Gas Installations.
IBR: Indian Boiler Regulations.
NACE MR – 0175: Sulfide Stress Cracking Resistant Metallic Materials for Oilfield Equipment.
NACE MR – 0284: Evaluation of Pipeline and Pressure Vessel Steel for Resistance to Hydrogen Induced Cracking.
NACE TM – 0177: Laboratory Testing of Metals for Resistance to Sulfide Stress Cracking in H2S Environment.
34. How do you support any small size HDPE/PVC (Plastic) pipe?
It should be supported continuously by using channel or Angle so that line should not sag or fall from the sleeper/rack due to uneven expansion because of Hot Temp.
35. Why do we provide High Point Vent (HPV) and Low Point Drain (LPD) in piping?
HPV – for removing Air during Hydro-test.
LPD – for draining water after conducting Hydro-test.
36. What do you mean by IBR and which lines come under IBR purview?
IBR = Indian Boiler Regulation Act.
Steam lines with conditions listed below comes under IBR purview –
Lines for which design pressure is 3.5 kg/sq cm and above.
Line size above 10” having design pressure 1.0 kg/sq cm and above.
Boilers feed water lines to steam generators, condensate lines to steam generators and flash drums.
37. What are Weldolet and Sockolet? And where are they used?
Weldolet and Sockolet are basically self reinforced fittings. Weldolet is used for Butt weld branch connection where standard tee is not available due to size restrictions and the piping is of critical / high pressure service. Sockolet is used for socket welding branch connections, which require reinforcing pad.
38. What is the MOC for Super heated high pressure Steam Lines?
A 335 Gr P I / P II, Composition: 0.5 Mo (P1) / 1.25 % Cr-.5% Mo (P11)
39. What is the normal upstream and downstream straight length of orifice flow meter?
Upstream - 15D Downstream - 5D
40. What are the essential data required for the preparation of equipment layout?
1) PFD and P&ID 2. Project Design data 3. Equipment Sizes & Buildings
41. What are the various statutory requirements to be considered during layout?
State Industrial Development Corporation (SIDC)
Central / State Environmental Pollution Control Boards (PCBS)
Factory Inspectorate
State Electricity Boards
Chief Controller of Explosives (CCOE)
Static & Pressure Vessel Rules (SMPV)
Tariff Advisory Committee
Aviation Laws
Chief Inspector of Boilers (CIB)
Oil Industry Directorate (OISD)
Food and Drug Administration (FDA)
Ministry of Environment and Forest (MoEF)
42. What do you mean by Insulated Joint?
Insulating Joints are a prefabricated, non-separable union used to isolate specific sections of Pipelines to prevent corrosion caused by stray electrical currents or interference from other pipelines and power transmission cables.
43. What do you mean by Composite Flange?
The flange that is made up of more than one MOC is called a Composite flange.
A. Lap Joint Flanges. Insert Flanges are a specialty in the arena of pipe size flanges and consist of two parts - the insert and the flange ring. The flange ring is the outer part of the insert flange assembly, containing the boltholes. The two-piece construction of the insert flange also offers the economy of matching the insert material to the process pipe (usually some corrosion resistant alloy) while the outer flange ring may be manufactured from steel. When the environment requires the flange ring to be made of some alloy the rotating feature is still maintained.
B. RF flanges with Raised of one MOC and rest of the flange with different MOC
C. RF blind flange with an overlay of 90/10 Cuni for Seawater service.
44. What is meant by ‘PWHT’? Why is it required?
“POST WELD HEAT TREATMENT” This is done to remove residual stress left in the joint, which may cause brittle fracture.
45. Describe different types of destructive and non-destructive tests?
DESTRUCTIVE TEST: Bend test, Tensile test, Impact test, and Hardness test.
NON-DESTRUCTIVE TEST: DPT, MPT, Radiography and ultrasonic test
46. What are Insulating Gasket Kits?
Insulation gasket kits are designed to combat the effects of corrosion often found in flanged pipe systems. Galvanic corrosion between dissimilar metal flanges (flow of currents), flange insulation associated with cathodic protection of underground piping are also the places where Insulating gasket kits are used. It consists of
Gasket Neoprene faced Phenolic /Glass Reinforced Epoxy (G10)
Insulation sleeve Reinforced Phenolic/Nylon/Polyethylene/(G10)
Insulation washer Reinforced Phenolic/Nylon/Polyethylene/(G10)
Plated Washer Electro plated steel washer
47. What do you mean by Jacketed Piping?
Piping which is recognized as providing the most uniform application of heat to the process, as well as maintaining the most uniform processing temperatures where steam tracing is not capable of maintaining the temperature of fluid constant. Usually used for molten sulfur, Polymers service.
48. What is the minimum distance to be maintained between two welds in a pipe?
The rule of thumb is that the minimum distance between adjacent butt welds is 1D. If not, it is never closer than 1-1/2". This is supposedly to prevent the overlap of HAZ s. Minimum spacing of circumferential welds between center lines shall not be less than 4 times the pipe wall thickness or 25 mm whichever is greater.
49. What are the different hardness tests carried out?
Brinell Hardness Test
Rockwell Hardness test
Vicker Hardness Test
50. What is the relation between Brinell Hardness No and Rockwell Hardness No?
22 HRC (Rockwell Hardness) = 238 BHN (Brinell Hardness No) Harder
piping interview questions and answers
51. During fabrication you observed that one small crack appeared on a fresh plate, what type of measure you will take to obtain desired quality with minimum wastage?
First identify the exact length of crack by DP test. Drill on the end point to resist further crack. Remove the crack portion by cutting the strip.
52. What is the minimum thickness of pipe that requires stress relieving to be done as per B31.3?
19 mm thickness.
53. What is the difference between thermostatic and thermodynamic steam trap?
Thermostatic trap is actuated by temp differential and is economical at steam pressure less than 6 PSI. It is operated by the movement of liquid filled bellows or by bimetal elements, which may get damaged by water hammer. Thermodynamic traps are most suited to applications where the pressure downstream of the trap is always less than about ½ the upstream pressure. These are suitable for pressure higher than 8 PSI. Water hammer doesn’t affect it.
54. What is the code for sour service?
Code for sour service is NACE MR–0175), NACE: National Association of Corrosion Engineers.
55. What are glandless piston valves? Where are these used?
Glandless piston valves are maintenance free valves used in the steam service.
56. What is the objective of stress analysis?
1. To ensure that the stresses in piping components in the system are within allowable limits.
2. To solve dynamic problems developed due to mechanical vibration, fluid hammer, pulsation, relief valves, etc
3. To solve problems associated due to higher or lower operating temperature such as
a) Displacement stress range
b) Nozzle loading on connected equipments
c) Pipe displacements
d) Loads & moments on supporting structure
57. How much pressure should be the pressure for hydro-test?
Hydro test pressure should be calculated as follows except as provided against point no-4.
1. 1.5 Times of design pressure.
2. For a design temperature above the test temperature, minimum test pressure can be calculated as:
Pt = (1.5 X P X St) / S
Where:-
Pt = Minimum test pressure. P = Internal design pressure.
St = Allowable stress at test temperature.
S = Allowable stress as design temperature. (See SE in table A-1 or S in table B-1/2/3).
3. If a test pressure as per above would produce a stress in excess of the yield strength at test temp. The test pressure may be reduced to maximum pressure that will not exceed the yield strength at test temp.
4. If the test pressure of piping exceeds the vessel pressure and it is not considered practicable to isolate piping from vessel, the piping and vessel may be tested together at test pressure of the vessel when approved by owner and provided the test pressure for vessel is not less than 115% of piping design pressure adjusted for temperature as per point no 2.
58. How do you calculate the pipe spacing?
Pipe Spacing (mm) = (Do + Dt) / 2 + 25mm + Thickness of insulation (mm).
Where: D0 = OD of small size pipe (mm), Dt = OD of flange of large size pipe (mm).
59. How do you calculate the width of Pipe rack?
W = (f X n X s) + A + B. Where,
f: safety factor
= 1.5 if pipes are counted from PFD.
= 1.2 if pipes are counted from P&Id.
n : number of lines in the densest area up to size 450 NB
= 300 mm (estimated average spacing)
= 225 mm (if lines are smaller than 250 NB)
A: additional width for –
· Lines larger than 450 NB.
· For instrument cable tray / duct.
· For an electrical cable tray.
s: 300 mm (estimated average spacing)
: 225 mm (if lines are smaller than 250 NB)
B: future provision = 20% of (f X n X s) + A
60. Which fluid is used in heat exchanger in shell side and tube side?
Generally corrosive fluid is used from the tube side (as the tube can be easily replaced) and cleaner fluid is used from the shell side. Sometimes hot fluid is also used from the shell side.
61. What is Reynold’s number and what is the value of this up to which the flow is laminar?
It’s a dimensionless number to classify the nature of flow - Re= avd / f
Where: Re = Raynold’s no. a = density of fluid. D = diameter of pipe.
V = average velocity of fluid. F = viscosity of fluid.
Flow is laminar up to Re = 2100
62. Give some examples for occasional loads.
Wind, wave & earthquake
63. What are the steps involved in stress analysis (or any stress package carried out)?
1. Identify the potential loads that the piping system would encounter during the life of the plant
2. Relate each of these loads to the stresses and strains developed
3. Get the cumulative effect of the potential loads in the system
4. Decide the allowable limits the system can withstand without failure as per code
5. After the system is designed to ensure that the stresses are within safe limits
64. How do you carry out estimation?
1. Input from bid:
P&Id, Line list, Temperature, Pressure.
Overall plant layout and piping corridor plan.
Scope of work and the specifications for the job.
Specifications for materials like PMS and VMS.
2. Value addition:
Items like valves, flanges, specialty items, reducers can be estimated from P&Id.
Length of pipes, elbows, width of pipe rack can be estimated by referring to P & Id and overall plot plan.
No of tires (on rack) can be estimated by referring to the spacing required for pipes and also the space available.
MTO for steam traps, valves (for vent and drain) can be calculated by using thumb rules.
3. Loads:
Hydro test loads: Can be estimated by assuming all the pipes (on a grid) empty except some bigger size lines filled with water.
Actual operating loads: Gas lines to be considered as empty and rest of the lines to be considered as filled with the Fluid (which they are supposed to carry in operating condition).
The load whichever is higher from above two cases should be referred for structural loading.
65. What are the different types of stresses that may get generated within a pipe during normal operation?
Axial stresses (tensile / compressive), shear stresses, radial stresses, hoopes stresses.
66. How are the loads classified in the stress analysis package?
1. Sustained Loads 2. Occasional Loads 3. Displacement Loads (Self limiting stresses due to thermal effects)
67. What are the inputs for stress analysis of a piping system?
A) Pipe Size B) Fluid Temperature C) Pipe Material D) Model E) Design pressure F) Insulation Thickness G) Specific gravity H) Friction coefficient.
68. What are the sources of sustained loads generated in the piping system?
a. Pressure b. Dead weight of pipe and attachments
Sustained load is calculated as
weight of pipe with fluid + pressure load + load due to springs W+P1
69. How do you calculate the operating load?
W+P1+T1, T1 – load due to thermal expansion
70. Mention some of primary loads (Have their origin in force)
Dead weight, pressure, forces due to relief or blow down, force due to water hammer effects.
71. Mention some of secondary loads (Have origin in displacement)
Force on piping due to tank settlement
Vessel nozzle moving up due to expansion of vessel
Pipe expansion or contraction
Vibration due to rotating equipment
72. What is the desired life cycle for piping in operation?
Desired life cycle for piping in operation is 20 Years (7000 Cycles). The normal no. of cycles for which the displacement or thermal stresses are designed is 7000 cycles.
73. What is the failure theory subscribed under ASME B31.3?
(A) Maximum principal stress theory (rankine's theory)
(B) Maximum shear theory
(C) Tresca theory
Ans: (A)
74. What are the types of failures encountered in piping?
A. Catastrophic failure B. Fatigue failure
75. Select the failure stress range for fatigue failure due to thermal expansion as per B31.3.
(A) (1.6Cs+1.6Sh) f (B) 0.78 Sh (C) (1.25 Sc+0.25Sh) f (D) Sc+Sh
Ans: (C)
Sc and Sh = Basic allowable material stress in cold & hot conditions respectively.
f = is the stress range reduction factor(1 for 7000 cycles)
76. How do you calculate the stress developed due to thermal expansion?
Stress developed = Exe/ L
E = Young’s modulus e = Increase in length due to thermal expansion
L = Original length of the pipe
77. How do you calculate the thermal expansion in a pipe?
Thermal expansion e= a x L x Rise in temperature, where,
a = Coefficient of expansion L = Length of pipe
78. What do you mean by Stress Intensity Factor (SIF)? Give some examples
Stress Intensity Factor (SIF) is the ratio of maximum stress intensity to normal stress. It is used as a safe factor to account for the effect of localized stress on piping under respective loading. In piping it is applied to welds, fittings, branch connections etc where stress concentration and possible fatigue failure may occur.
Eg: SIF for reducer and weld neck flange: 1.0
SIF for socket weld flange: 1.3
79. Which are the criteria for pipe support?
Following are the points, which should be taken into account for proper supporting –
Load of bare pipe + fluid + insulation (if any).
Load of bare pipe + water fill.
Load of valves and online equipment and instruments.
Thermal loads during operation.
Steam out condition, if applicable.
Wind loads for piping at higher elevation, if required.
Forced vibration due to pulsating flow.
Bare pipe with size above 12” shall be supported with pad or shoe
80. What is the basic span of supports for 2”/6”/10”/24” pipe
Basic Span is 5.5m / 9m / 11.5m / 15m respectively.
81. How do we decide the anchor / cross guide and guide for offsite rack piping?
Anchor is provided to restrict all the axial and rotational movements of pipe, whereas cross guide is provided to restrict displacements of pipe along with the axis perpendicular to its centerline and guide is provided to restrict the longitudinal movements of pipes along with its axis.
82. What are the things to be taken care of while doing pump piping?
Pipe strain may distort equipment alignment, so welding should be done in such a way that the tension in the equipment flange is minimized.
83. Where do you provide anchor and slotted support for heat exchangers?
Anchor support of the heat exchanger is provided on the side from which the tube bundle will be pulled out for the purpose of maintenance work. It is based on the growth of the connecting piping, as the exchanger should grow with the piping.
84. What do you mean by hoop stresses and how do you calculate it?
Stresses which are generated circumferentially due to the action of internal pressure of the pipe are called hoop stress. It is calculated by
Hoop stress (Sh) = Pdo / 4t
Where, P = Force Acting from Inside. Do = OD of Pipe. t = Pipe Thickness.
85. How does hoop stress affect the system?
As per membrane theory for pressure design of cylinders, as long as hoop stress is less than yield stress of Moc, the design is safe. Hoop stress induced by thermal pressure is twice the axial stress (SL). This is widely used for pressure thickness calculation for pressure vessels.
86. What is the design standard followed for the calculation of allowable forces / moments in nozzles of centrifugal compressor & Steam turbines nozzle?
For strain sensitive equipment piping00 to be routed and supported to limit nozzle loadings and moments in equipment within allowable limits furnished by respective vendors or in absence of vendor data API 560/610/615/621/661 & NEMA SM23.NEMA – SM 23 (referred by API 617) is used for compressor & steam turbine nozzle.
87. What is the mill tolerance to be considered for the thickness of pipe during stress analysis as per ASME B31?
(A) 1% (B) 2.5%
(C) 7.5% (D) 12.5%
Ans: D
88. What is the purpose of providing graphite pads in supports below shoes?
To reduce the friction factor. The coefficient of friction for graphite pads is 0.1
89. How is piping to the tank inlet nozzle supported and why?
Piping to tank nozzles is supported with spring type support (first support from nozzle) in order to make the nozzle safe from the loads, which occurs due to the displacement of pipe (thermal expansion of pipe / tank material, tank settlement etc).
90. What are the two types of flexible spring hangers?
1. Constant Spring and 2. Variable Spring
91. Differentiate between static load and dynamic load.
A piping system may respond far differently to a dynamic load than it would to a static load of the same magnitude. Static loads are those, which are applied slowly enough that the system has time to react and internally distribute the loads, thus remaining in equilibrium. In equilibrium, all forces and moments are resolved (i.e., the sum of the forces and moments are zero), and the pipe does not move.
With a dynamic load—a load which changes quickly with time—the piping system may not have time to internally distribute the loads, so forces and moments are not always resolved—resulting in unbalanced loads, and therefore pipe movement. Since the sum of forces and moments are not necessarily equal to zero, the internally induced loads can be different either higher or lower than the applied loads.
92. What is WRC 107 / WRC 297?
Localized stresses at nozzle to Shell are calculated by WRC 107 / 297 and these computed stress values shall be limited in accordance with ASME Sec VIII for pressure vessels.
93. Give different types of dynamic loads with examples.
1. Random – Wind, Earthquake 2. Harmonic – Equipment Vibration, Pulsation, Acoustic Vibration 3. Impulse – Fluid Hammer, Relief Valve Opening, Slug Flow
94. What is the maximum expansion absorbed in loops in normal design?
10 Inches
95. What is the limiting factor in deciding the length of the spool in jacketed piping?
Force exerted by dissimilar expansion of inner pipe = Force exerted by dissimilar expansion of jacket pipe. The stress developed due to this should be within limits as per ANSI B31.3 (Also fabrication constraints)
96. What is the allowable stress range for CS pipes?
2070 kg/cm 2
97. What is the factor to be checked concerning the expansion of header attached to air cooler piping?
Vendor drawing to be checked to see how much movement is permitted to compensate for line expansion. To accommodate the diff. Expansion between inlet and outlet (The inlet temperature >The outlet temperature) offset can be built into outlet piping to compensate for difference expansion. Since the tubes are of floating design the nozzle flange is of 150# and loads transferred are to be kept minimum. Since the tubes are of floating design, the nozzle flange is 150#. Load of the nozzle to be kept minimum.
98. What is the maximum no. of cell nozzles connected to a single header of air cooler piping header in normal practice?
Six nos.
99. What are the insulation materials used for piping systems?
A. Fibrous – Rock & Glass Wool
B. Rigid - Calcium Silicate, Polyisocyanurate, Cellular Glass
100. What is the purpose of expansion below?
Expansion bellows are used absorb axial compression or extension, lateral shear or angular torsion developed in the pipes (specially near nozzles)
101. What is dynamic analysis and why is it used?
Dynamic analysis is performed for all two phase lines in order to ensure that the line supported is safe from vibrations loads which may occur during normal operation as well as in start-up or any upset condition. (Diesel mixed with hydrogen in DHDT process)
102. What should be the material of shoes for supporting pipes & why?
If CS shoes are used Pad in contact with the pipe to be of alloy steel to avoid dissimilar welding at pipe. To avoid alloy steel welding and dissimilar welding fabricated clamps either of CS or SS can be used.
103. In an offsite pipe rack change in direction during analysis it is found two adjacent pipes are having unequal expansion with the inner pipe having 50 cm thermal expansion. What can be done to eliminate collisions during hot conditions?
Use cold pull technique. Calculate the thermal expansion of the inside pipe, cut an equal length form the elbow joint and then reweld with a shorter length to take care of expansion in hot condition.
104. What are sway braces?
Sway braces are essentially a double-acting spring, housed in a canister. Unlike variable effort supports, Sway braces are not intended to carry the weight of pipe work; their purpose is to limit undesirable movement. Sway braces act like a rigid strut until a small preload is reached, where after the restraining force increases in proportion to the applied deflection.
Undesirable movement can occur due to many phenomena, such as wind loading, sympathetic vibration, rapid valve closure, relief valve opening, two phase flow or earthquake. It may be necessary to limit this type of deflection to prevent the generation of unacceptable stresses and equipment loadings.
The sway brace is a cost-effective means of limiting pipe work deflection. It should be noted however that it does provide some resistance to the thermal movement of the pipe work and care should be taken when specifying to ensure that this is acceptable. Installation of sway braces will have the effect of raising the fundamental frequency of vibration of a pipe work system; this is likely to reduce undesirable deflections. Sway braces are often used to solve unforeseen problems of resonant vibration. For situations where the resistance to thermal movement provided by Sway braces is unacceptable, you are referred to as pipe supports with a limited range of hydraulic snubbers and dampers.
105. What is a fluid hammer and how is it generated?
When the flow of fluid through a system is suddenly halted at one point, through valve closure or a pump trip, the fluid in the remainder of the system cannot be stopped instantaneously as well. As fluid continues to flow into the area of stoppage (upstream of the valve or pump), the fluid compresses, causing a high-pressure situation at that point. Likewise, on the other side of the restriction, the fluid moves away from the stoppage point, creating a low pressure (vacuum) situation at that location. Fluid at the next elbow or closure along the pipeline is still at the original operating pressure, resulting in unbalanced pressure force acting on the valve seat or the elbow. The fluid continues to flow, compressing (or decompressing) fluid further away from the point of flow stoppage, thus causing the leading edge of the pressure pulse to move through the line. As the pulse moves past the first elbow, the pressure is now equalized at each end of the pipe run, leading to a balanced (i.e., zero) pressure load on the first pipe leg. However the unbalanced pressure, by passing the elbow, has now shifted to the second leg. The unbalanced pressure load will continue to rise and fall in sequential legs as the pressure pulse travels back to the source (or forward to the sink). The ramp up time of the profile roughly coincides with the elapsed time from full flow to low flow, such as the closing time of the valve or trip time of the pump. Since the leading edge of the pressure pulse is not expected to change as the pulse travels through the system, the ramp down time is the same. The duration of the load from initiation through the beginning of the down ramp is equal to the time required for the pressure pulse to travel the length of the pipe leg.
106. What is the difference between variable spring hanger and constant spring hanger?
Variables use coiled springs to support a load and allow movement. The resistance of the coil to a load changes during compression, which is why these devices are called "variables". Constant spring hanger provides constant support force for pipes and equipment subjected to vertical movement due to thermal expansion at locations where maintaining a constant stress is critical. This constant resistance is achieved by having two moment arms pivoted about a common point. The load is suspended from one of these arms, and a spring is attached to the other. With an appropriate choice of moment arms and spring properties, a resisting force can be provided that is nearly independent of position. Constant support hangers are principally used to support pipes and equipment subjected to vertical movement due to thermal expansion at locations where transfer of stress to other supports or equipment can be critical. The maximum recommended variation according to MSS standard from the operating load is 25% for variable spring hangers. If the variation exceeds 25%, a constant support hanger should be used. The constant resistance to a load is achieved by combining a spring coil with a cam, which rotates about a main pivot point. The cam is designed such that the distances from the main pivot changes to compensate for the variable resistance during compression of the coil. The MSS standard provides for a tolerance of 6% in the constant load through the travel range. Constant support hangers are designed per MSS, ANSI, and ASME standards. The sizing of constants primarily depends on the total travel and load.
107. How to get the foundation loads?
Foundation Loads for pipe rack should include the loads of Pipes, Cable Trays and Instrumentation duct at that location and also the design load for future tier shall be full load of the most heavily loaded tier in addition to all other wind/seismic/fraction and piping thermal loads for future pipes. Load of pipes filled with water (Largest of
1st case – During hydro testing dead weight (wt/m X pipe rack spacing) of pipes + 2 –3 maximum size pipes filled with water.
2nd case – Actual commissioned condition except the gas lines) + Proportionate wt of extra space required by client (normal 30%) + Load of 1 heavily loaded tier + Electrical cables + Instrument duct + Guide load for 50% of lines Guide Load = 0.3X (Dead wt of pipes at including water)
The maximum induced thermal loads on the Anchor at the battery limit shall be limited to
F in kg <= 150 X NB of pipe in inches (It should be <2 tones)
M in Kgm <=75 X NB of pipe in inches.
Horizontal Load = 0.3 X (Dead wt of pipes including water)
This load is used for designing foundation bolts. Foundation loads for any vessel having agitators mounted on top should contain the weight of the tank at operating or design condition (whichever is more) plus 20% of it for dynamic loading.
piping interview questions
1.What are the types of compressors?
Positive displacement, centrifugal and axial, rotary screw, rotary vane, rotary lobe, dynamic, liquid ring compressors.
2.What are the types of compressor drives?
Electric motor, gas turbine, steam turbine and gas engine.
3.How centrifugal compressors work?
High speed impellers increase the kinetic energy of the gas, converting this energy into higher pressures in a divergent outlet passage called a diffuser. Large volume of gas at moderate pressure.
4.What are the types of steam turbines and why are they popular?
Condensing and non-condensing, popular because they can convert large amounts of heat energy into mechanical work very efficiently.
5.Where gas turbine drive is used?
Desserts and offshore platforms where gas is available, for gas transmission, gas lift, liquid pumping, gas re-injection and process compressors.
6.What is the auxiliary equipment of the compressor?
Lube oil consoles, seal oil consoles, surface condensers, condensate pump, air blowers, Intel air filters, waste heat system, compressor suction drum, knock out pot, pulsation dampener, volume bottles, inter and after coolers.
7. What are the types of seal oil systems?
Gravity and pressurized.
8. What factors to be considered while designing compressor housing?
Operation, maintenance, climate conditions, safety, economics.
9. What are the compressor housing design points?
Floor elevation, building width, building elevation, hook centerline elevation
10. What are the types of compressor cases?
Horizontal split case, vertical split case.
11. What are compressor suction line requirements?
Minimum 3D straight pipe between elbow and inlet nozzle, increases based on inlet piping layout 4D
12. What are necessary parts of the inlet line of the compressor?
Block valve, strainer, break out flanges in both inlet and outlet to remove casing covers, straightening vane in inlet line if not enough straight piece in inlet line available, PSV in inter stage line and in discharge line before the block valve.
13. What points to be considered for reciprocating compressor piping layout?
High pulsation, simple line as low to grade as possible for supporting, analog study, all branches close to line support and on top, isolate line support from adjacent compressor or building foundations
14. What are the types of compressor shelters?
On ground with no shelter, open-sided structure with a roof, curtain wall structure (temperature climates), open elevated installation, elevated multi-compressor structure
piping systems in process piping
1. What is the ASME code followed for design of piping systems in process piping (refineries chemical industries)?
A) B31.1 B)B31.3 C)B31.5 D)B31.9
Ans: (B)
2. What do you mean by the following items?
A)ISLB-400 B)ISMB-600 C)ISHB-350 D)ISMC-300 E)ISJB-150 F)ISLB-200 G)ISMB-450 H)ISWB-400 I)ISJC-200 J)ISLC-350 K)ISMC-250
Ans:
A - Indian STD lightweight beam, web size-400
B - Indian STD medium weight beam, web size-600
C - Indian STD 'H' beam, web size-350
D - Indian STD medium weight channel, web size-300
E - Indian STD junior beam, web size-150
F - Indian STD lightweight beam, web size-200
G - Indian STD medium weight beam, web size-450
H - Indian STD wide flange beam, web size-400
I - Indian STD junior channel, web size-200
J - Indian STD lightweight channel, web size-350
K - Indian STD medium weight channel, web size-250
3. What is this item?
A)ISA-100X100X12 B)ISA-80X50X10 C)ISLT-100X100
Ans: A) Equal angle size 100 X 12 THK B) Unequal angle size 80X50X12 THK C)Indian STD lightweight tee bar size 100X100
4. What is the difference between stub in and stub on branches? Which one is preferred?
Ans: For branching of one size lesser of run pipe, stub on is preferred. For other branching less than one size of run pipe stub in is preferred. The design is based on ANSI B31.3.
5. What is the difference between Pipe and Tube?
Ans: Pipe is identified by NB and thickness is defined by schedule whereas Tube is identified by OD.
6. From which size on-wards NB of pipe is equal to OD of pipe?
Ans: From the size 14'' and on-wards NB = OD of pipe.
7. Write down the outside diameter of the following pipe?
A) 3 inch B) 6 inch C) 10 inches D) 14 inch
Ans: A) 3 inches = 88.9mm B) 6 inches = 168.28mm C) 10 inch = 273.06mm D)14 inch = 355mm (OD = sizeX25.4)
8. What is the difference between machine bolt and stud bold?
Ans: Machine bolt has a head on one side and not on other side but stud bolt has nuts on both sides.
9. What is a soluble dam?
Ans: Soluble dam is a water-soluble material used for restricting the purging gas within the pipe.
10. While welding the pipe trunnion to pipe/reinforcement pad you have to put a hole or leave some portion of welding why?
Ans: For venting of hot gas which may get generated due to welding.
conclusion
The question topics in the piping engineer interviews include technical questions, managerial questions and soft skills. Stress analysis and piping design skills together with the ability to conform to ASME and API are the major criteria employed in evaluating candidates. Questions also arise concerning AutoCAD or CAESAR II software, planning and estimating the cost of the project, and how to relay these to the clients. Experience in construction, in maintenance and the related legal issues is important as well as the capability for problem solving, dealing with a team and showing leadership skills. Leading candidates should have technical skills, good project management skills and good interpersonal skills for this challenging field of piping engineering.